Elenco Strandbeest Bedienungsanleitung PDF herunterladen (Seite 15)

27 28

6. Attach the second frame.

Second frame

Joints

Crankshaft

7. Attach legs to make three sets.

[3] Putting the body together

1. Attach the two body assemblies together.

Fold the rubber band into two loops, and position it so that

the tops of the frames pass through it.

Attach the second frame

firmly to the first frame, so

as to sandwich the legs that

you put together in Steps 2

to 5. Line up the three

joints on the frames, and

position the slot in the

middle of the frame so that

it snaps into place on the

central axis of the

crankshaft.

2. Insert the shafts (long) into the frames.

3. Attach the stoppers.

Stopper

[4] Attaching the wind turbine

Affix two strips of double-sided tape to

each of the T-shaped ends on the wind

turbine base. Remove the paper on one

side of the double-sided tape and affix

the tape over the protrusions on the

wind turbine base as shown in the

diagram below, but leave the paper on

the up side remaining for now. You

will end up affixing a total of 10 strips

of double-sided tape to the wind

turbine base.

Fold over about 1/3

of the double-sided

tape to make it

easier to remove it

from the paper

backing it comes on.

Double-sided tape

1. Attach the blades.

Remove the paper backing on the up

side of each strip of double-sided

tape, and attach each blade so that

the two holes on each blade line up

with the protrusions on the wind

turbine base. Do the same for all five

blades to attach them.

Use the remaining parts to make one more assembly just like this.

Repeat Steps 2 to 6 until you

have assembled three pairs of

legs for a total of six legs on

four frames, connected to the

crankshaft. This completes

one half of the body of the

Mini Strandbeest.

Insert the shafts (long) into the holes on the frames shown in the diagram.

Adjust the shafts (long) so that they stick out on either end by a small amount.

After completing these adjustments, pull on each rubber band loop and hook

them around the ends of the frames.

Attach the right and left sides of the body

together, making sure that the legs are not

positioned in the same way. If the legs are

all positioned the same way, turn the joint

on the crankshaft 180° on one side only.

There are two extra

strips used as

spares.

* Check to make sure that the legs move

smoothly by turning the crankshaft. If the

legs do not move correctly, go back to Step 5

and check to make sure that the rods are in

the correct order.

* If the frames do not seem to be attached

together properly, make sure that each

frame is firmly attached to the crankshaft.

Attach the two body assemblies together, oriented so that the joints on

the frames and crankshaft face in the same direction. When attaching,

fold the rubber band over into a double loop, and position the loops in

between the joints on the tops of the frames on the assemblies.

Attach stoppers to the protrusions on the frames on either end of the

body (three on each side for a total of six).

Shaft (long)

Wind turbine base

Blade

Protrusions

2. Insert the cogwheel shaft into the body.

Cogwheel shaft

3. Attach the cogwheels

After attaching the cogwheel (small) to the crankshaft axis, attach the

cogwheel (large) to the cogwheel shaft and push it in until it snaps into

place.

Cogwheel shaft

Crankshaft

Cogwheel (large)

Cogwheel

(small)

4. Attach the wind turbine.

Use the shaft (short) to attach the wind turbine to the stopper part on

the top of the frame on the side on which the cogwheels are attached.

Attach the tube (small) to the end of the shaft (short) to keep the wind

turbine in place and prevent it from falling out.

Wind turbine

Finished

Getting the Mini

Strandbeest to Walk

● Using wind to make it move

● Using the rotating shaft to make it move by hand

You can wave a round paper fan or

a folding fan toward it or use an

electric fan to blow air at it. Once

wind hits it, the Mini Strandbeest

will start walking toward the left

as seen from the side of the wind

turbine.

Use the tube (large) to connect the rotating shaft and flange together.

Remove the wind turbine from the Mini Strandbeest as the weight will

drag it down, and then insert the flange into the crankshaft. When you

turn the rotating shaft, the Mini Strandbeest will start to walk.

Flange

Tube (large)

When you turn the rotating

shaft, the Mini Strandbeest will

walk to the same direction in

which the shaft is being turned.

Be careful not to turn it so hard

that the tube gets too twisted.

Tube (small)

Shaft (short)

Rotating shaft

Turn the cogwheel shaft while

pushing on it to firmly attach

it.

Make sure to leave

about 1 to 2 mm of space

open between the tube

and the wind turbine to

ensure that the wind

turbine rotates

smoothly.

Insert the cogwheel shaft into two frames on the body. Once you have

inserted it into the second frame, turn the cogwheel shaft 90° so that it

snaps into place.

1 2 ... 10 11 12 13 14 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Elenco Strandbeest Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Spielzeuge Elenco Strandbeest