Elenco Strobe Light and Sound Bedienungsanleitung PDF herunterladen

If you have any problems, contact Elenco

(800) 533-2441 Fax: (847) 520-0085 ● e-mail: [email protected] ● Website: www.elenco.com or www.snapcircuits.net

ARNING: SHOCK HAZARD -

ever connect Snap Circuits

to the electrical outlets in your

ome in any way!

ARNING: Always check your wiring before

turning on a circuit. Never leave a circuit

unattended while the batteries are installed.

Never connect additional batteries or any other

power sources to your circuits.

Strobe Light & Sound

Model SCP-14

753163

Project 3

Strobe Light &

Sound

Snap Circuits

uses electronic blocks that snap onto a base grid to build different

circuits. These blocks have different colors and numbers on them so that you can

easily identify them. Build the circuit shown by placing all the parts with a black 1 next

to them on the clear base grid first. Then, assemble parts marked with a 2. Connect

the white LED (D6) using the red & black jumper wires as shown, with red wire to “+”

side. Install three (3) “AA” batteries (not included) into the battery holder (B3).

Turn on the slide switch (S1). The white LED should be flashing. Move the lever on

the adjustable resistor (RV) to adjust the flash rate a little.

Note: In rare cases the circuit may not work at all settings of RV. If this happens,

move the RV lever to the side near the strobe IC (U23), and only move the RV lever

over a small range.

Combine projects 1 & 2 by stacking

the white LED (D6) and speaker

(SP2) together as shown. Remember

to connect the red wire to the “+” side

of the LED. This circuit is shown on

the box cover.

Project 1 Strobe Light

Placement

Level Numbers

Project 2 Strobe Sound

Replace the white LED (D6) with the speaker (SP2); the speaker doesn’t have a “+”

side, so the red wire can go to either side. Turn on the slide switch (S1). You hear a

clicking sound from the speaker. Move the lever on the adjustable resistor (RV) to

adjust the clicking rate a little.

CAUTION: Persons who are extremely

ensitive to flashing lights should exercise

caution when playing with this toy.

AUTION:

igh intensity light. Do not

look directly at the white LED (D6).

Project 4

Suspended

Raindrops

Use the circuit from project 1. Go to a

water faucet and adjust the faucet so

water is dripping at a steady rate.

Dim the room lights and hold the

white LED so it shines on the

dripping water. Try to set the lever on

the adjustable resistor (RV) so that

the dipping water drops appear

suspended in mid-air. You may need

to adjust the drip rate on the faucet to

make this work.

Faucet

Turn on the switch (S1)

and move the lever on the

adjustable resistor (RV)

to change the brightness

of the white LED (D6).

Project 5 Adjustable Light

SCP-14_022014.qxp_SCP-14 Instructions 3/7/14 2:37 PM Page 1

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Strobe Light & Sound

Seite 2

Project 7 Persistence of VisionUse the circuit from project 6, but replace the speaker (SP2) withthe white LED (D6); connect the red wire to

Seite 3 - Project 11 Musical Shapes

Build the circuit as shown; note that the speaker (SP2) is a tight fiton the strobe IC (U23), but does fit. Turn on the switch (S1). Makeyour parts us

Seite 4 - PRODUCTS! PARTS LIST

Important: If any parts are missing ordamaged, DO NOT RETURN TORETAILER. Call toll-free (800) 533-2441 ore-mail us at: [email protected]

Kommentare zu diesen Handbüchern

Keine Kommentare

Elenco Strobe Light and Sound Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Spielzeuge Elenco Strobe Light and Sound herunter. Elenco Strobe Light and Sound User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Spielzeuge Elenco Strobe Light and Sound